Victron Energy Smart Battery Protect 12/24V 100A

BPR110022000 - The Victron Energy Smart Battery Protect 12/24V 100A protects the battery against excessive discharge and can be used as a system on/off switch The Smart Battery Protect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch.

Item Number:
BPR110022000
Your Price:
£63.95
Points:
11 Worth £0.55
Your Total:
Quantity:
Description

Battery Protect BP-100 Specifications

  • Max. continuous load current* 100A
  • Peak current (during 30 seconds) 600A
  • Operating voltage range 6 –35V
  • Current consumption When on: 1,4 mA When off or low voltage shutdown: 0,9 mA
  • Alarm output delay 12 seconds
  • Maximum load on alarm output 50 mA (short circuit proof)
  • Load disconnect delay 90 seconds (immediate if triggered by the VE.Bus BMS)
  • Load reconnect delay 30 seconds
  • Default thresholds Disengage: 10,5V or 21V Engage: 12V or 24V
  • Operating temperature range Full load: -40°C to +40°C (up to 60% of nominal load at 50°C)
  • IP rating Electronics: IP67 (potted)
  • Connections: IP00 Connection: M8
  • Weight: 0,5 kg
  • Dimensions (hxwxd) 59 x 42 x 115 mm

Features of the - Victron Energy Smart Battery Protect 12/24V 100A

12/24V auto ranging -

The Smart Battery Protect automatically detects system voltage one time only.

Bluetooth: programming made easy -

When using Bluetooth to program the Smart Battery Protect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.

A special setting for Li-ion batteries -

In this mode the Battery Protect can be controlled by the VE.Bus BMS. Note: the Battery Protect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.

Ultra-low current consumption -

This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.

Over voltage protection -

To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.

Ignition proof -

No relays but MOSFET switches, and therefore no sparks.

Delayed alarm output -

The alarm output is activated if the battery voltage drops below the pre-set disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.

Delayed load disconnect and delayed reconnect -

The load will be disconnected 90 seconds after the battery voltage drops below the pre-set level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the pre-set reconnect voltage.


PRODUCT CODE: BPR110022000




Reviews

You Might Also Like...

Sunshine Solar Limited
Your Cart
Your Cart: Empty

Need Help? 01508 488 188 - Mon-Fri 9AM - 5PM

Categories
Location
Home / Store / Victron Products / Victron Energy Smart Battery Protect 12/24V 100A

Newsletters Signup

Sign up to Our Newsletter to receive special offers

card Logos
© 2024 Sunshine Solar Limited, all rights reserved worldwide.
Kryptronic eCommerce, Copyright 1999-2024 Kryptronic, Inc. - https://kryptronic.com/ [0.039968 / 1.408997]